穿條機工作時需要調整完善，其調整步驟如下：

　　The threading machine needs to be adjusted and perfected during operation, and the adjustment steps are as follows:

　　安裝與水平調整 ：

　　Installation and horizontal adjustment:

　　安裝擺好主機及料架，并調好水平。

　　Install and arrange the host and material rack, and level them properly.

　　接上電源及氣源，開機空轉3分鐘，檢查轉動系統是否工作正常。

　　Connect the power and air source, run the machine idle for 3 minutes, and check if the rotating system is working properly.

　　齒輪與膠條調整 ：

　　Gear and rubber strip adjustment:

　　搖動頂蓋上部左右手輪，使驅動膠條的兩個齒輪上升，使上下兩個齒輪空間超過膠條的高度。

　　Shake the left and right handwheels on the top cover to raise the two gears that drive the rubber strip, so that the space between the upper and lower gears exceeds the height of the rubber strip.

　　將膠條推動導向槽，使之與兩轉動齒輪剛好接觸。

　　Push the rubber strip towards the guide groove to make it just in contact with the two rotating gears.

　　搖動頂蓋上部左右手輪往下調整驅動齒輪使之壓緊膠條，一般以能手感敏捷無多余間隙即可。

　　Shake the upper left and right handwheels of the top cover to adjust the driving gear downwards and press the rubber strip tightly. Generally, it should feel agile and have no excess clearance.

　　鎖緊上部左右手輪與之連接的絲桿，以防止絲桿在工作時轉動而引起驅動齒輪往上提或向下掉。

　　Lock the screw rods connected to the upper left and right handwheels to prevent them from rotating during operation and causing the drive gear to lift up or fall down.

　　導向槽與型材中心距調整 ：

　　Adjustment of center distance between guide groove and profile:

　　調整石滑座，使兩條導向槽的中心距與要穿條型材的兩穿條槽中心等值，鎖定滑座。

　　Adjust the stone slide seat so that the center distance between the two guide grooves is equal to the center of the two threading grooves of the profile to be threaded, and lock the slide seat.

　　主機與輔架調整 ：

　　Host and auxiliary rack adjustment:

　　將型材放在輔架水平面上，調整主機垂直大滑座，將兩膠條導向槽與材兩穿條槽調到同一個水平。

　　Place the profile on the horizontal surface of the auxiliary frame, adjust the vertical sliding seat of the main machine, and adjust the two rubber strip guide grooves and the two material threading grooves to the same level.

　　按隔熱型材產品組合圖放好再往主機的定位處輕輕頂進，將定位件調好并鎖定。

　　Place the insulation profile product combination diagram and gently push it into the positioning position of the host, adjust the positioning part and lock it.

　　調整輔架尾座，使在穿條時氣缸非常大行程的頂板端面到主機定位處之間的距離與型材長度相當，鎖定尾座。

　　Adjust the tailstock of the auxiliary frame so that the distance between the top plate end face of the maximum stroke of the cylinder and the positioning position of the main engine during threading is equivalent to the length of the profile, and lock the tailstock.

　　托料平臺與機頭調整 ：

　　Material platform and machine head adjustment:

　　調整和安裝好兩面的托料平臺。

　　Adjust and install the material support platforms on both sides.

　　先放入一根型材，用手調整該機頭的左右移動手輪，將“導向定位塊”調整到機器出條槽口和鋁型材穿條槽口一致；如需要上下調整則按動“刀盤上升”和“刀盤下降”來調整機頭的高度。

　　First, place a profile and manually adjust the left and right movement handwheel of the machine head to align the "guide positioning block" with the machine strip slot and the aluminum profile strip slot; If you need to adjust up and down, press "cutterhead up" and "cutterhead down" to adjust the height of the machine head.

　　再放入上面的兩根開好齒的鋁型材，調整后面托料架子上的“定位板”，頂住鋁型材。

　　Place the two toothed aluminum profiles on top again, adjust the "positioning plate" on the material rack at the back, and press against the aluminum profiles.

　　穿條操作 ：

　　Wearing operation:

　　用人工將隔熱條順導向槽口送入鋁型材槽口內一點。

　　Manually guide the insulation strip into the slot of the aluminum profile to a certain point.

　　踩下設備上的腳踏開關，齒刀加壓轉動，將隔熱條高速送入鋁型材槽口，穿條完畢后，松開腳踏開關。

　　Step on the foot switch on the device, apply pressure and rotate the toothed knife, and quickly feed the insulation strip into the aluminum profile slot. After threading the strip, release the foot switch.

　　重復以上步驟，加工下一根鋁型材。

　　Repeat the above steps to process the next aluminum profile.

　　速度調節 （針對全自動穿串機）：

　　Speed regulation (for fully automatic threading machines):

　　打開全自動穿串機，確保機器處于正常工作狀態。

　　Turn on the fully automatic threading machine and ensure that it is in normal working condition.

　　找到機器上的調速按鈕或旋鈕，通常位于機器的控制面板上。

　　Find the speed control button or knob on the machine, usually located on the control panel of the machine.

　　調節按鈕或旋鈕，逐漸增加或減少機器的速度，直到達到所需的速度。

　　Adjust the button or knob to gradually increase or decrease the speed of the machine until the desired speed is reached.

　　調節速度時應該逐步調整，不要一下子調節過快或過慢，以免影響機器的穩定性和穿線質量。

　　When adjusting the speed, it should be gradually adjusted, and not adjusted too fast or too slow at once, so as not to affect the stability and threading quality of the machine.

　　調節完畢后，將機器上的線桿和線輪按要求放置好，開始進行穿線操作。

　　After the adjustment is completed, place the wire rod and wire wheel on the machine as required, and start the threading operation.

　　建議：在調整穿條機時，務必仔細檢查每個部件的位置和狀態，確保所有連接牢固，避免在操作過程中發生故障。調整完畢后，進行多次空轉檢查，確保設備運行平穩。

　　Suggestion: When adjusting the threading machine, be sure to carefully check the position and status of each component to ensure that all connections are secure and avoid malfunctions during operation. After adjustment, perform multiple idle checks to ensure smooth operation of the equipment.

　　本文來自：穿條機更多的內容請點擊：http://www.fuhuei.cn我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

　　This article is from: Strip threading machine. For more content, please click: http://www.fuhuei.cn We will provide satisfactory service for the questions you ask. Welcome to call us!